KVM currently supports savevm/loadvm and offline or live migration Migration commands are given when in qemu-monitor (Alt-Ctrl-2). Upon successful completion, the migrated VM continues to run on the destination host.
You can migrate a guest between an AMD host to an Intel host and back. Naturally, a 64-bit guest can only be migrated to a 64-bit host, but a 32-bit guest can be migrated at will.
There are some older Intel processors which don't support NX (or XD), which may cause problems in a cluster which includes NX-supporting hosts. We may add a feature to hide NX if this proves to be a problem in actual deployments.
- The VM image is accessible on both source and destination hosts (located on a shared storage, e.g. using nfs).
- It is recommended an images-directory would be found on the same path on both hosts (for migrations of a copy-on-write image -- an image created on top of a base-image using "qemu-image create -b ...")
- The src and dst hosts must be on the same subnet (keeping guest's network when tap is used).
- Do not use -snapshot qemu command line option.
- For tcp: migration protocol
- the guest on the destination must be started the same way it was started on the source.
highlights / merits
- Almost unnoticeable guest down time
- Guest is not involved (unique to KVM Live Migration [#1 1])
- Capability to tunnel VM state through an external program (unique to KVM Live Migration [#1 1])
- ssh/gzip/bzip2/gpg/your own
- Upon success guest continues to run on destination host, upon failure guest continues to run on source host (with one exception)
- Short and Simple
- Easy to enhance
- Hardware independence (almost).
- Support for migration of stopped (paused) VMs.
Anchor(1) 1 These features are unique to KVM Live Migration as far as I know. If you know of other hypervisor that support any of them please update this page or let me (Uri) know.
The user interface is through the qemu monitor (alt-ctrl-2 on the SDL window)
migrate [-d] <URI> migrate_cancel
The '-d' will let you query the status of the migration.
With no '-d' the monitor prompt returns when the migration completes. URI can be one of 'exec:<command>' or tcp:<ip:port>
migrate_set_speed <speed> set bandwidth control parameters (max transfer rate per second)
Example / HOWTO
A is the source host, B is the destination host:
- __TCP__ example:
1. Start the VM on B with the exact same parameters as the VM on A, in migration-listen mode (-incoming tcp:0:4444 (or other PORT)) 2. Start the migration (always on the source host):
A: migrate -d tcp:B:4444 (or other PORT)
3. Check the status (on A only):
- __Offline__ example:
1. unlimit bandwidth used for migration:
A: migrate_set_speed 1g
2. stop the guest:
3. continue with either TCP or exec migration as described above.
Problems / Todo
- TSC offset on the new host must be set in such a way that the guest sees a monotonically increasing TSC, otherwise the guest may hang indefinitely after migration.
- usbdevice tablet complains after migration.
- handle migration completion better (especially when network problems occur).
- More informative status.
- Migration does not work while CPU real-mode/protected mode are still changing.
savevm/loadvm to an external state file (using pseudo-migration)
- let the state file be /saved_images/VM.STATE
- savevm (qemu monitor):
stop migrate file:///saved_images/VM.STATE
- loadvm (qemu command line and qemu monitor):
<qemu-command-line> -incoming file:///saved_images/VM.STATE cont
more exec: options
- To be supported directly by Migration Protocols, but until then...
- Save VM state into a compressed file
* Save stop migrate_set_speed 4095m migrate "exec:gzip -c > STATEFILE.gz"
* Load gzip -c -d STATEFILE.gz | <qemu-command-line> -incoming stdio
- Save VM State into an encrypted file (assumes KEY has already been generated)
* Save stop migrate_set_speed 4095m migrate "exec:gpg -q -e -r KEY -o STATFILE.gpg"
- Load VM state from an encrypted file
gpg -q -d -r KEY STATEFILE.gpg | <qemu-command-line> -incoming stdio
- Send encrypted VM state from host A to host B (Note: ssh is probably better, this is just for show)
* on host A migrate "exec:gpg -q -e -r KEY | nc B 4444" * on host B nc -l 4444 | gpg -q -d -r KEY | <qemu-command-line> -incoming stdio
Algorithm (the short version)
1. Setup * Start guest on destination, connect, enable dirty page logging and more 2. Transfer Memory * Guest continues to run * Bandwidth limitation (controlled by the user) * First transfer the whole memory * Iteratively transfer all dirty pages (pages that were written to by the guest). 3. Stop the guest * And sync VM image(s) (guest's hard drives). 4. Transfer State * As fast as possible (no bandwidth limitation) * All VM devices' state and dirty pages yet to be transferred 5. Continue the guest * On destination upon success * Broadcast "I'm over here" Ethernet packet to announce new location of NIC(s). * On source upon failure (with one exception).
Instructions for kvm-13 and below: MigrationQemu0.8.2.