How to assign devices with VT-d in KVM
- In order to assign devices in KVM, you'll need a system which supports VT-d, not to be confused with the VT-x support of your CPU. VT-d needs to be supported by both your motherboard chipset and your CPU.
- If you are in doubt whether your motherboard or CPU supports VT-d, the Xen VT-d wiki has some information about VT-d enabled chipsets, motherboards, and CPUs:
- If your hardware does not have an IOMMU (known as "Intel VT-d" on Intel-based machines and "AMD I/O Virtualization Technology" on AMD-based machines), you will not be able to assign devices in KVM.
- Assigning graphics cards is not officially supported at the moment, but there has been some success passing through a secondary Radeon HD 5850 as a VM's secondary display.
Assigning the device
1. Modify the kernel config
- Navigate to the kernel source code directory (usually located in /usr/src/linux) and configure the kernel:
cd /usr/src/linux make menuconfig
- Navigate to "Bus options (PCI etc.)" and enable the following options:
Support for DMA Remapping Devices Enable DMA Remapping Devices PCI Stub driver
- Optionally, this can also be enabled:
Support for Interrupt Remapping
- Save the changes and exit
2. Build the kernel
make make modules_install make install
3. Reboot and verify that your system has IOMMU support
- AMD-based machines:
dmesg | grep AMD-Vi ... AMD-Vi: Enabling IOMMU at 0000:00:00.2 cap 0x40 AMD-Vi: Lazy IO/TLB flushing enabled AMD-Vi: Initialized for Passthrough Mode ...
- Intel-based machines:
dmesg | grep -e DMAR -e IOMMU ... DMAR:DRHD base: 0x000000feb03000 flags: 0x0 IOMMU feb03000: ver 1:0 cap c9008020e30260 ecap 1000 ...
Note: If you get no output, you will need to fix this before moving on. Try the following:
- Verify that your hardware supports VT-d and that it has been enabled in the BIOS.
- Check dmesg for errors suggesting that the BIOS is broken.
- CONFIG_DMAR_DEFAULT_ON is not set. Pass one of the following commands as a kernel parameter:
intel_iommu=on # Intel only iommu=pt iommu=1 # AMD only
Note: The kernel parameter can be passed temporarily using the GRUB menu by highlighting the OS, pressing "e", and appending the parameter to the end of the line beginning with "linux".
4. Unbind the device from the host kernel driver (Example: PCI device 01:00.0)
- Load the PCI Stub Driver if it is compiled as a module
modprobe pci_stub lspci -n
- Locate the entry for device 01:00.0 and note the vendor and device ID (8086:10b9 in this example)
... 01:00.0 0200: 8086:10b9 (rev 06) ...
- Place this information in the following files:
echo "8086 10b9" > /sys/bus/pci/drivers/pci-stub/new_id echo "0000:01:00.0" > /sys/bus/pci/devices/0000:01:00.0/driver/unbind echo "0000:01:00.0" > /sys/bus/pci/drivers/pci-stub/bind
5. Load the KVM modules
modprobe kvm modprobe kvm-intel
6. Assign the device
/usr/local/bin/qemu-system-x86_64 -m 512 -boot c -net none -hda /root/ia32e_rhel5u1.img -device pci-assign,host=01:00.0
VT-d device hotplug
KVM also supports hotplug devices with VT-d to guest. In guest command interface (you can press Ctrl+Alt+2 to enter it), you can use following command to hot add/remove devices to/from guest:
- hot add:
- hot remove:
- VT-d spec specifies that all conventional PCI devices behind a PCIe-to PCI/PCI-X bridge or conventional PCI bridge can only be collectively assigned to the same guest. PCIe devices do not have this restriction.
- If the device doesn't support MSI, and it shares IRQ with other devices, then it cannot be assigned due to host irq sharing for assigned devices is not supported. You will get warning message when you assign it. Notice this also apply to the devices which only support MSI-X.